# Leach flutter on balanced lug

**URL:** <https://forum.clcboats.com/t/leach-flutter-on-balanced-lug/72734>\
**Category:** Builder's Forum\
**Created:** [November 16, 2026, 8:31pm UTC](https://forum.clcboats.com/t/leach-flutter-on-balanced-lug/72734 "2026-11-16T20:31:19Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![Chris\_Jackson1](https://avatars.discourse-cdn.com/v4/letter/c/958977/32.png) [@Chris\_Jackson1](https://forum.clcboats.com/u/Chris_Jackson1)\
**Post date:** [November 16, 2026, 8:31pm UTC](https://forum.clcboats.com/t/leach-flutter-on-balanced-lug/72734/1 "2026-11-16T20:31:19Z")

</div>

I’ve had my Lake Union Swift out for just a few sails after completing it last month, and now, sadly, it’s time to put it away until spring.

While I have a fair amount of sailing experience, it’s all been on Bermuda rigged sloops or windsurfers. So far I’m liking the balanced lug (62 sq ft, same sail and spars as the Skerry, Passagemaker, Tenderly, and NE Dory), but I’ve got a lot to learn about how to best optimize it under different sailing conditions.

I’ve got the halyard and downhaul attachments at the points shown on the plans, and I’ve got a 3:1 purchase on the downhaul, having read about the importance of sufficient tension there. My mainsheet also follows the plans with a becket block on the boom near the clew, and the mainsheet starting at the becket, going down to a block on a transom-mounted bridle line, back up to the aft boom block, and forward to a second block on the boom about halfway to the mast.

So far, so good, with the only concern being that when winds are maybe in the 12-14 knot range (the most I’ve seen so far), I’m getting a good bit of leach flutter going upwind. This breeze wasn’t sustained enough for me to try any tweaks other than downhaul tension, but I couldn’t get rid of it just with that, and cranking down pretty hard. I have not yet sailed with a reef in.

Any suggestions for how to tame it? I’ve had leach lines on bigger boats, but don’t want to go that route here. Wondering if moving the downhaul aft some might help? Maybe tighter lashing/outhauls on the spars? Could too much downhaul be a factor?

This isn’t a huge concern for me, and if I were out in any more wind I would want to reef, and maybe that’s the solution right there?

Thanks for any insights.

---

<div class="post-metadata">

**Author:** ![Mark\_Nye](https://yyz1.discourse-cdn.com/flex007/user_avatar/forum.clcboats.com/mark_nye/32/18_2.png) [@Mark\_Nye](https://forum.clcboats.com/u/Mark_Nye)\
**Post date:** [November 17, 2026, 1:01pm UTC](https://forum.clcboats.com/t/leach-flutter-on-balanced-lug/72734/2 "2026-11-17T13:01:06Z")

</div>

Bermuda rigged boats use a boomvang to control leach tension and prevent flutter in higher winds. The simple lug rigging default on the CLC lug rigged boats has no such control.

If you want better control of your lug, suggest that you read these articles by Michael Storer, designer of the Goat Island Skiff: [20 ways to boost Lug rig and lug sail performance! Rigging and Tuning. - Storer Boat Plans in Wood and Plywood](https://www.storerboatplans.com/tuning/lug-rig-setup/everything-lug-rig-and-lug-sail/) .

This picture shows the pertinent mainsail controls on my GIS. The halyard is on the right side of the mast. On the left is the “vanghaul” which controls both luff and leach tension. Note that it is basically just the downhaul with the boom attachment further aft. The boom attachment is movable so you can adjust forward for more “downhaul” and aft for more “boomvang.”

The other change is addition of a “bleater” which prevents the vanghaul from pulling the boom forward. This is the line that runs horizontally looped around the boom and mast and is cleated (other side) to the boom forward of the mast.

In practice, once you find the length of bleater and vanghaul position best for your boat, you will not have to change them. I have marked best location for both to speed rigging before launch.

One last point is that running the halyard and vanghaul aft is a good idea. Allows for both adjustment of the vanghaul and raising/lowering of the sail without moving forward.

 ![40140037063_10553fb951_o](https://canada1.discourse-cdn.com/flex007/uploads/clc/original/2X/1/1b98400681ee7854c61ecaa41f0c67fb0efdd96c.jpeg)

---

<div class="post-metadata">

**Author:** ![Jeff\_Richards](https://yyz1.discourse-cdn.com/flex007/user_avatar/forum.clcboats.com/jeff_richards/32/29_2.png) [@Jeff\_Richards](https://forum.clcboats.com/u/Jeff_Richards)\
**Post date:** [November 17, 2026, 2:22pm UTC](https://forum.clcboats.com/t/leach-flutter-on-balanced-lug/72734/3 "2026-11-17T14:22:24Z")

</div>

Your running rigging set-up sounds like everything is in the correct places. I have a NE Dory with about the same set-up. As I’m sure you’ve noticed, the balanced lug can develop a lot of twist when close-hauled in higher winds. The clew of the upper boom spar tends to drift off to leward. First, I don’t think a leach line will do anything at all, probably just serve to hook the leach and turn your sail into a 4-sided bag - no clean air departing the leach edge. While the boom vang is a key control for sail shape on a reach and run, it also probably doesn’t have the “strength” needed when close hauled.

For all of the discussion below, note that your rig will need bleater lines or a wrap of line with parallel beads or some other arrangement (like shown in Mark Nye’s pictures) to basically “fix” the fore-aft position of your booms to the mast, and it also helps keep things consistent between port/starboard tacks if your system keeps the booms close against the mast. Booms running free, banging around and moving in, out, fore and aft held only by a long downhaul and a long halyard don’t let you accomplish any usefull adjustments with vangs or downhauls or mainsheets or halyard tension (or anything).

I think the key to controlling leach flutter (and balanced lug sail shape) when close hauled is getting good down-tension from the mainsheet, and meanwhile controlling how much the upper boom can drift to leward. I’d try two things to see if they help.

First, see if you can rig your bridle with more line - let it form a larger triangle with the mainsheet block at the apex. (I’m assuming you are using a running block or shackle on the bridle, that it isn’t fixed to a center point.) The looser bridle will allow the block to run out to the leward side a little farther, maybe a couple of inches, thus give more downward vertical pull on the boom, rather than lateral pull. On my NE Dory I have fake hemp line (not so slippery) and use a shackle to connect the lower mainsheet block to the bridle, not a rolling block. There is enough friction between the shackle and the bridle line that when sailing upwind I frequently reach out and push the block outboard and the friction will keep it there, again, gaining a few inches to outboard. You could get really creative and rig some sort of adjustable traveler/bridle system, but that might create a lot of complications in adjusting with each tack that you’d otherwise like to avoid. Bottom line, wherever the correct position of the boom is for your windward point of sail, the more your mainsheet is pulling down rather than inboard (the closer the lower mainsheet block is to being over the leward gunwale) will probably create the biggest improvement you’ll see, as compared to any other factor like vang position, tension, etc..

The second thing I’ve done is to just slightly “lanteen” my balanced lug set up. I think the boat just sails better that way. What I’m saying is that my luff is not vertical - I’ve rigged things so my upper boom is 2-3 inches further forward. This seems to just give me a better overall balance to the rig, sail shape, speed, more balanced helm, less leward drift of the upper boom (the booms stay more parallel) and when close hauled, and a tighter leach. This does raise the outer (clew) end of the boom a bit, but that doesn’t seem to be a bad thing, either. If you’ve seen competetive Sunfish sailors, they move the boom connection so far forward that the upper lanteen boom almost becomes an extension of the mast - turning the Sunfish into a Bermuda or Marconi rig. Not exactly what you can do with the balanced lug sail, but a little bit of the same effect, and I presume with a goal for the same overall impact.

When you get back on the water let us know what you try, and what works for you.

Edit: I was re-reading you post and noted that your bidle is transom mounted. Based on hull shape for the Swift, that is probably where it should stay and you gain little from trying to move it any further forward. But if it moving the bridle forward doesn’t interfere with other things, and is easy to do, and gains you any significant movement of your lower main block position further outboard, that might be something you consider. On something with a pinched stern like the NE Dory or Skerry, getting the bridle further forward and “underneath” the mainsheet block on the boom clew is of great benefit. I rig my bridle on the NE Dory throught the after set of oarlocks. (I have 3 oarlock sets, thus allowing for dual rowers.)

---

<div class="post-metadata">

**Author:** ![Chris\_Jackson1](https://avatars.discourse-cdn.com/v4/letter/c/958977/32.png) [@Chris\_Jackson1](https://forum.clcboats.com/u/Chris_Jackson1)\
**Post date:** [November 17, 2026, 8:06pm UTC](https://forum.clcboats.com/t/leach-flutter-on-balanced-lug/72734/4 "2026-11-17T20:06:12Z")

</div>

Thanks Jeff and Mark for these tips! I’ve read through the various Storer articles before, but it was a lot to take in before actually hitting the water. Moving the downhaul aft of the mast makes a lot of sense for keeping the leech tighter, and the “bleater” line to keep the boom from being pulled forward looks like a pretty easy solution. I’ll rig that up.

Playing with the bridle length and the point where the mainsheet attaches also makes sense. I have the mainsheet block lashed to a low friction ring on the bridle line, which is dyneema, so the block slides along the line easily, maybe too easily. I’ll get more friction into that interface to get more downward (less inward) tension on the clew. (Given the small cockpit area, I think I need to keep the bridle on the transom.)

All logical and pretty easily implemented measures–the best kind! If only I didn’t have to wait 3 or 4 months to give them a try.

---

<div class="post-metadata">

**Author:** ![Laszlo\_Morocz](https://avatars.discourse-cdn.com/v4/letter/l/c68b51/32.png) [@Laszlo\_Morocz](https://forum.clcboats.com/u/Laszlo_Morocz)\
**Post date:** [November 18, 2026, 12:53am UTC](https://forum.clcboats.com/t/leach-flutter-on-balanced-lug/72734/5 "2026-11-18T00:53:22Z")

</div>

Chris,

You don’t have to wait 4 months if your boat is on a trailer. Set it up with all the rigging on a day that has a nice steady wind, turn the trailer to the appropriate angle relative to the wind and try out all your tricks. The boat doesn’t have to be moving or in the water for the sails and rigging to work.

I actually worked out the reefing system, parrel and lazyjacks for my CLC Peapod, the roller furling system for my West Wight Potter 15, the bridle for my sprit rig on my Brand X dinghy and the entire rig for my Bolger schooner on dry land, so I can tell you that it works.

No worries about ice, launching and retrieving, dropping stuff into the water, capsizing or needing a tow back to shore. Don’t need to run back home to get that forgotten tool or piece of line and you can dress as warm as needed without a PFD. And there’s a hot drink inside.

Laszlo
