# Rudder Cable Assembly Questions

**URL:** <https://forum.clcboats.com/t/rudder-cable-assembly-questions/36877>\
**Category:** Builder's Forum\
**Created:** [May 5, 2010, 5:22pm UTC](https://forum.clcboats.com/t/rudder-cable-assembly-questions/36877 "2010-05-05T17:22:34Z")\
**Posts on this page:** 10\
**Page:** 1

<div class="post-metadata">

**Author:** ![Jeff\_Hovis](https://avatars.discourse-cdn.com/v4/letter/j/4da419/32.png) [@Jeff\_Hovis](https://forum.clcboats.com/u/Jeff_Hovis)\
**Post date:** [May 5, 2010, 5:22pm UTC](https://forum.clcboats.com/t/rudder-cable-assembly-questions/36877/1 "2010-05-05T17:22:34Z")

</div>

Does anyone have any photos of their cable runs from the rudder to the peddles?&nbsp; I’m having trouble visualizing how it passes through the deck and/or bulkhead.&nbsp; Are there any sharp bends?

---

<div class="post-metadata">

**Author:** ![pag](https://avatars.discourse-cdn.com/v4/letter/p/e19adc/32.png) [@pag](https://forum.clcboats.com/u/pag)\
**Post date:** [May 7, 2010, 11:16am UTC](https://forum.clcboats.com/t/rudder-cable-assembly-questions/36877/2 "2010-05-07T11:16:39Z")

</div>

Jeff,

I am still willing to email you some pictures, but as I said, I do not do postings - no time to figure that out.&nbsp; Anyway, I made deck fairleads similar to those done by dehager.&nbsp; I used a piece of dowel.&nbsp; Drilled it down the center and then cut it at the desired angle.&nbsp; After gluing them to the deck, I redrilled thru the hole in the dowel and thru the deck.&nbsp; I drilled the aft bulkhead right up in the corners near the sheer clamp and threaded the tubing from cockpit back to the deck penetration.&nbsp; The tubing was then epoxyed into the fairleads and attacheck to the sheer clamps with cable clips.&nbsp; The forward end of the tubing ends near the aft end of the foot brace assemblies.&nbsp; All the angles and turns are very gentle.&nbsp; The control line for raising and lowering the rudder is run thru several deck rigging loops and terminated in a jam cleat next to the cockpit..&nbsp; All works well.&nbsp; this is the Smart Track system by the way.

Paul G.

---

<div class="post-metadata">

**Author:** ![Jeff\_Hovis](https://avatars.discourse-cdn.com/v4/letter/j/4da419/32.png) [@Jeff\_Hovis](https://forum.clcboats.com/u/Jeff_Hovis)\
**Post date:** [May 7, 2010, 4:18pm UTC](https://forum.clcboats.com/t/rudder-cable-assembly-questions/36877/3 "2010-05-07T16:18:45Z")

</div>

Thanks Paul.&nbsp; That’s pretty much what I posted last night.&nbsp; So now I know it will work.&nbsp; Thanks for the info.

---

<div class="post-metadata">

**Author:** ![Jeff\_Hovis](https://avatars.discourse-cdn.com/v4/letter/j/4da419/32.png) [@Jeff\_Hovis](https://forum.clcboats.com/u/Jeff_Hovis)\
**Post date:** [May 7, 2010, 4:48pm UTC](https://forum.clcboats.com/t/rudder-cable-assembly-questions/36877/4 "2010-05-07T16:48:03Z")

</div>

Paul, did you buy the short or long pin version of the Smart Trac?

---

<div class="post-metadata">

**Author:** ![Dana\_Hager](https://avatars.discourse-cdn.com/v4/letter/d/c6cbf5/32.png) [@Dana\_Hager](https://forum.clcboats.com/u/Dana_Hager)\
**Post date:** [May 5, 2010, 8:05pm UTC](https://forum.clcboats.com/t/rudder-cable-assembly-questions/36877/5 "2010-05-05T20:05:34Z")

</div>

It really depends on the rudder and foot braces but this is what I did with a K2 rudder and SeaDog Foot Control&nbsp;pedals.

&nbsp;http://dehager.smugmug.com/Boats/CLC-Mill-Creek-165/6686487\_BbGBe

&nbsp;

![](http://dehager.smugmug.com/Boats/CLC-Mill-Creek-165/P3200080/607914358_TZYSX-S.jpg)

![](http://dehager.smugmug.com/Boats/CLC-Mill-Creek-165/rudder-knee/846327762_vPdnw-S.jpg)&nbsp;

![](http://dehager.smugmug.com/Boats/CLC-Mill-Creek-165/rudder-tube/846328743_B7jpd-S.jpg)

![](http://dehager.smugmug.com/Boats/CLC-Mill-Creek-165/P4260043/853094460_MVvFT-S-1.jpg)&nbsp;

![](http://dehager.smugmug.com/Boats/CLC-Mill-Creek-165/P4260043/853094460_MVvFT-S-1.jpg)&nbsp;

---

<div class="post-metadata">

**Author:** ![Jeff\_Hovis](https://avatars.discourse-cdn.com/v4/letter/j/4da419/32.png) [@Jeff\_Hovis](https://forum.clcboats.com/u/Jeff_Hovis)\
**Post date:** [May 5, 2010, 8:50pm UTC](https://forum.clcboats.com/t/rudder-cable-assembly-questions/36877/6 "2010-05-05T20:50:09Z")

</div>

Your assembly is the one I was hoping to see.&nbsp; The only thing I can't really see is how the cable winds up in the cockpit.&nbsp; I see it goes through the rear bulkhead, so I assume it passes throught the aft deck somehow.&nbsp; Do you have a photo of that?&nbsp; My rudder is probably going to be a retrofit.&nbsp; I'll probably have to go through the side decking for mine since I'll have the decks on before I get to a rudder.

BTW, I am really considering the Sea-Dog peddles and even the SeaLect TruCourse rudder.&nbsp; Did you look at that one?

---

<div class="post-metadata">

**Author:** ![pag](https://avatars.discourse-cdn.com/v4/letter/p/e19adc/32.png) [@pag](https://forum.clcboats.com/u/pag)\
**Post date:** [May 6, 2010, 10:35am UTC](https://forum.clcboats.com/t/rudder-cable-assembly-questions/36877/7 "2010-05-06T10:35:43Z")

</div>

Jeff,

I do not get this picture posting stuff.&nbsp; Old dogs and new tricks I guess.&nbsp; If however you can give me an email address I will send a pciture showing how I penetrated the deck for the cables on my Shearwater,

Paul G.

---

<div class="post-metadata">

**Author:** ![Jeff\_Hovis](https://avatars.discourse-cdn.com/v4/letter/j/4da419/32.png) [@Jeff\_Hovis](https://forum.clcboats.com/u/Jeff_Hovis)\
**Post date:** [May 6, 2010, 10:56am UTC](https://forum.clcboats.com/t/rudder-cable-assembly-questions/36877/8 "2010-05-06T10:56:44Z")

</div>

Thanks Paul,

For picture posting you need a hosting site such as photobucket.com&nbsp; It is a free photo hosting site.&nbsp; Once you have pics stored there, you simply click on the photo you want to include here.&nbsp; A box will open with the following options:

Email & IM

Direct Link

HTML Code

IMG Code

Select the Http address in the direct link field and copy it.&nbsp; Then, in this text box there is a little icon at the bottom that looks like a tree.&nbsp; Click on it and paste that address into the field that says Image URL.&nbsp; Then click on Insertand the picture will automatically load into this text box.

&nbsp;

---

<div class="post-metadata">

**Author:** ![Dana\_Hager](https://avatars.discourse-cdn.com/v4/letter/d/c6cbf5/32.png) [@Dana\_Hager](https://forum.clcboats.com/u/Dana_Hager)\
**Post date:** [May 6, 2010, 1:41pm UTC](https://forum.clcboats.com/t/rudder-cable-assembly-questions/36877/9 "2010-05-06T13:41:18Z")

</div>

I made two wood fairleads to run the housing through the deck. I also added a Delrin bushing for the K2 rudder.

&nbsp;

![](http://dehager.smugmug.com/Boats/CLC-Mill-Creek-165/P5050046/858856230_VZTsc-S.jpg)

![](http://dehager.smugmug.com/Boats/CLC-Mill-Creek-165/rudder-bushing/846326764_iqfZQ-S.jpg)

![](http://dehager.smugmug.com/Boats/CLC-Mill-Creek-165/drill-bushing/846298782_w4nPz-S.jpg)

---

<div class="post-metadata">

**Author:** ![Jeff\_Hovis](https://avatars.discourse-cdn.com/v4/letter/j/4da419/32.png) [@Jeff\_Hovis](https://forum.clcboats.com/u/Jeff_Hovis)\
**Post date:** [May 6, 2010, 3:36pm UTC](https://forum.clcboats.com/t/rudder-cable-assembly-questions/36877/10 "2010-05-06T15:36:38Z")

</div>

Thanks!&nbsp; That is prettly slick.&nbsp; All I have to do is figure out how to do something similar. Maybe a dowel cut down the middle with a hole drilled through?

Paul, I'd still like to see yours if you can put up a picture.
