# Skeg kit

**URL:** <https://forum.clcboats.com/t/skeg-kit/41512>\
**Category:** Builder's Forum\
**Created:** [October 30, 2013, 9:10am UTC](https://forum.clcboats.com/t/skeg-kit/41512 "2013-10-30T09:10:18Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![Michael\_Morry](https://avatars.discourse-cdn.com/v4/letter/m/fbc32d/32.png) [@Michael\_Morry](https://forum.clcboats.com/u/Michael_Morry)\
**Post date:** [October 30, 2013, 9:10am UTC](https://forum.clcboats.com/t/skeg-kit/41512/1 "2013-10-30T09:10:18Z")

</div>

Has anyone attached a premade skeg kit, not made of wood, to a kayak?

I am concerned about adhering plastic to wood which I'm assuming that a premade kit would be make from, such as the one sold by Superior Kayaks.

Thanks,

Mike

---

<div class="post-metadata">

**Author:** ![Howard\_Spira](https://avatars.discourse-cdn.com/v4/letter/h/ec9cab/32.png) [@Howard\_Spira](https://forum.clcboats.com/u/Howard_Spira)\
**Post date:** [October 30, 2013, 8:08pm UTC](https://forum.clcboats.com/t/skeg-kit/41512/2 "2013-10-30T20:08:14Z")

</div>

Mike,

i have personal experience with the superior kayak kit and retrofitting it onto an arctic hawk.

the superior kayak skeg that i bought about 5 years ago was fibreglass (not plastic)&nbsp;and a first rate kit.&nbsp; i had no problem getting it to adhere and have had it in place since then with no problem.&nbsp;&nbsp; i think the key is that this is a very well done part built with the same epoxy/glass approach as the hull of the clc boat (except there is no wood in it).&nbsp; Its installation follows the technique you would expect of doing fibreglass to&nbsp;fibreglass &nbsp;attachment&nbsp;where you will have a mechanical (vs chemical) bond.&nbsp;the prep is roughing it up and cleaning it appropriately before epoxing it in place.&nbsp; in addition,&nbsp;you build a&nbsp;small&nbsp;glass fillet that bonds it solidly with the hull.

it is a very well designed and strongly engineered.&nbsp; it looked very professional and &nbsp;i got a lot of positive comments on it.&nbsp;&nbsp; i did not trust some of the 'plastic' kits that i also investigated.&nbsp;&nbsp; that said, it was an expensive kit....but i think you get what you pay for.

mark rogers at superior, was also really solid on installation support.

i just checked in at superior kayak's site. it looks like they have not changed the construction (still fibreglass)&nbsp; i am currently building a new strip-built night heron and looking to potentially add a skeg....if i do....it will be from superior.&nbsp;

&nbsp;

&nbsp;

---

<div class="post-metadata">

**Author:** ![Michael\_Morry](https://avatars.discourse-cdn.com/v4/letter/m/fbc32d/32.png) [@Michael\_Morry](https://forum.clcboats.com/u/Michael_Morry)\
**Post date:** [October 31, 2013, 8:27am UTC](https://forum.clcboats.com/t/skeg-kit/41512/3 "2013-10-31T08:27:50Z")

</div>

hspira,

Thanks for the info, that's what I needed. I tried contacting Superior, but I have not heard back yet. I also heard that CLC is planning a skeg kit similar to what is included in the S&G petrel kit, but it's only $10-15 less than a ready made kit. I think I'll go with the pre-made kit.

&nbsp;

Mike

&nbsp;
