# Work bench question?

**URL:** <https://forum.clcboats.com/t/work-bench-question/43790>\
**Category:** Builder's Forum\
**Created:** [January 22, 2016, 5:07pm UTC](https://forum.clcboats.com/t/work-bench-question/43790 "2016-01-22T17:07:03Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![Lou\_Volpe](https://avatars.discourse-cdn.com/v4/letter/l/b19c9b/32.png) [@Lou\_Volpe](https://forum.clcboats.com/u/Lou_Volpe)\
**Post date:** [January 22, 2016, 5:07pm UTC](https://forum.clcboats.com/t/work-bench-question/43790/1 "2016-01-22T17:07:03Z")

</div>

My NE Dory was shipped today and i just about have my garage squared away with enough room [I hope] to build.&nbsp; I have a workbench for my mixing station and I am going to build a few horses.&nbsp; Looking at a some of the photos on the site, I see guys gluing the puzzle parts together on the floor, on a bench, on horses, etc.&nbsp; I was thinking of getting a 4"x8" sheet of ply, cutting in half and using three horses to glue up the pieces, then once i start assemblying the hull remove the ply and simplly use the horses.&nbsp; Any comments on this approach.&nbsp; Suggestions?

&nbsp;

&nbsp;

---

<div class="post-metadata">

**Author:** ![Robert\_Whitehurst](https://avatars.discourse-cdn.com/v4/letter/r/85e7bf/32.png) [@Robert\_Whitehurst](https://forum.clcboats.com/u/Robert_Whitehurst)\
**Post date:** [January 22, 2016, 6:04pm UTC](https://forum.clcboats.com/t/work-bench-question/43790/2 "2016-01-22T18:04:04Z")

</div>

&nbsp; &nbsp;The puzzle joints are tight. &nbsp;Mine required a fair bit of pressure and a rubber mallet to get them all together. &nbsp;I used 3/4" plywood under each joint, on the floor, so I could get medieval on it. &nbsp;Up on a 1/2" plywood on horses, it bounced and flexed. &nbsp;The ends of the planks were propped up to the same thickness with scrap pieces because I didn't have a single big piece of plywood. &nbsp;The thick plywood is convenient to screw into for clamping also. &nbsp;

---

<div class="post-metadata">

**Author:** ![Peter\_Shapiro](https://avatars.discourse-cdn.com/v4/letter/p/e480ec/32.png) [@Peter\_Shapiro](https://forum.clcboats.com/u/Peter_Shapiro)\
**Post date:** [January 22, 2016, 7:53pm UTC](https://forum.clcboats.com/t/work-bench-question/43790/3 "2016-01-22T19:53:35Z")

</div>

&nbsp; &nbsp;If you add a couple of 4x4's on top of the horses and under the ply, it will give you a very stable surface to work on. &nbsp;Get the straightest 4x4's you can find. &nbsp;And I used 3/4" &nbsp;2-sided melamine instead of ply, as glue, epoxy, and paint tend to wipe off fairly easily. &nbsp;The weight of the melamine will hold the 4x4's in place, making it unnecessary to fasten them down. &nbsp;When you're done with the project, everything comes apart and is easily stacked against the wall in your garage, ready for the next time and taking up little space.

---

<div class="post-metadata">

**Author:** ![Carl\_Karickhoff](https://avatars.discourse-cdn.com/v4/letter/c/ccd318/32.png) [@Carl\_Karickhoff](https://forum.clcboats.com/u/Carl_Karickhoff)\
**Post date:** [January 23, 2016, 5:18pm UTC](https://forum.clcboats.com/t/work-bench-question/43790/4 "2016-01-23T17:18:31Z")

</div>

I put my aluminum extension ladder on two horses and then 1/2 inch ply on top. &nbsp;Very stable and flat.

---

<div class="post-metadata">

**Author:** ![Dick\_Dowdell](https://yyz1.discourse-cdn.com/flex007/user_avatar/forum.clcboats.com/dick_dowdell/32/43_2.png) [@Dick\_Dowdell](https://forum.clcboats.com/u/Dick_Dowdell)\
**Post date:** [January 24, 2016, 9:23am UTC](https://forum.clcboats.com/t/work-bench-question/43790/5 "2016-01-24T09:23:27Z")

</div>

Oceanlluvr,

This link might be of interest.

[http://www.clcboats.com/forum/clcforum/thread/32362.html](http://www.clcboats.com/forum/clcforum/thread/32362.html)

Cheers,

Dick

---

<div class="post-metadata">

**Author:** ![David\_Poole](https://avatars.discourse-cdn.com/v4/letter/d/82dd89/32.png) [@David\_Poole](https://forum.clcboats.com/u/David_Poole)\
**Post date:** [January 24, 2016, 12:49pm UTC](https://forum.clcboats.com/t/work-bench-question/43790/6 "2016-01-24T12:49:12Z")

</div>

&nbsp;&nbsp;&nbsp;Essentially it don't matter how you do it as long as it provides a stable,. flat &nbsp;work space.

Take a look at this video.

[https://www.youtube.com/watch?v=pwmAQzUta88&index=3&list=PL8E4DB9EC74DA8888](https://www.youtube.com/watch?v=pwmAQzUta88&index=3&list=PL8E4DB9EC74DA8888)

&nbsp;
